These steels are more responsive to mechanical and heat treatments than carbon steels. AISI 8620 alloy steel is a common, carburizing alloy steel. This alloy steel is flexible during hardening treatments, thus enabling improvement of case/core properties. The following datasheet will provide more details about AISI 8620 alloy steel. AR400 & AR500 Wear Plate & Bar Specialty Steel Co.Typical Properties of AR400. AR400 is thru-hardened, abrasion resistant, alloy wear plate. Hardness range is 360/440 BHN with a nominal hardness of 400 BHN. Service Temperature is 400°F. This plate product is intended for use in applications where a good balance of formability, weldability, toughness and abrasion resistance are required.
Our AR400 steel plates meet all flatness and thickness requirements the 50% standards that are specified in ASTM A-6. All of the mechanical properties for the abrasion resistance steel matches the ASTM AR400 Steel PlateAR400 Abrasion Resistant Steel Plates 1.65 MM THICKNESS x WIDTH 1000 MM / 1250 MM / 1400 MM / 2000 MM / 2400 MM X LENGTH 1000 MM / 2400 MM / 3000 MM / 6000 MM / COIL CUT in AR400 Abrasion Resistant Steel Plates, AR400 Wear Resistant Steel Plates, AR400 Wear Plates. ASTM A572 Grade 50, 55, 60, 65 Steel Plates Specification A:Specimen shall comply with Specification of A6/A6M. B:Elongation not required to be determi ed for floor plate. C:For wide flange shapesover 426 lb/ft [634 kg/m], elongation in 2 in. [50 mm] of 19% minimum applies. D:For plates wider than 24 in. [600 mm], the elongation requirement is reduced two percedntage points for Grade 42, 50, and 55 [290,345,and 380], and three percentage points
3.1 If the desired mechanical properties are as described in 4.1.1 for material identified as Classes P-1 through P-7, or in 4.1.2 for material identified as Classes Q-1 through Q-7, the strength level desired can be based on hardness or the equivalent tensile or yield strength as shown in Tables 1-4. Abrasion wear resistant steel plate - AR235,AR400,AR450 The AR400 are premium abrasion resistant steel plates that are heat-treated and exhibit through-hardening. Improved forming and weding capabilities. AR450 is an abrasion resistant plate used in a variety of applications where slightly greater strength is desired beyond AR400. Abrasion-Resistant Steel:Properties and Applications
Our goal and commitment to our customers is to provide outstanding on time service. As a company we have endeavored to set the pace in the competitive steel market. Hardox 400 - Easy to form, wear-resistant steel from SSAB Hardox® 400 is a wear- and abrasion-resistant steel with a nominal hardness of 400 HBW. It combines high toughness, good bendability and weldability. Mechanical Properties of Structural Steelscombination of mechanical damage, natural variability, and differences in testing methodology. High-strain-rate properties for selected perimeter and core column steels include yield and tensile strength, total elongation and strain rate sensitivity for rates up to 400 s-1. Measured properties
AR400 F Steel Plate is formable grade of Abrasive Resistance Steel Plate designed to accomodate applications where a life of wear is the primary cause for failure among other grades of steel plate.AR400 abrasive resistance steel plate is intended for higher, impact, wear applications where cold-bending and very good weldability is important. Section F - EMJMecHAnicAL PRoPeRtieS Applicable to Structural Quality. Reduction of Area Min . elon-AStM Yield tensile gation over A 514 Strength Strength in 2 3/4 & 3/4 Grade thickness (psi) (psi) Min . Under thick Minimum B & c Up to 11/4 incl. 100,000 110/130,000 18% 40% 50% Speedy Metals Information for ASTM A572 Grade 50 PlateGrade 50 conforms to ASTM A572. MECHANICAL PROPERTIES. The above values are average and may be considered as representative of ASTM A572 Grade 50 Elongation in 8":16%. APPLICATIONS. ASTM A572 Grade 50 is considered a "workhorse" grade and is widely used in many applications. Steel mills produce channel and heavy beams with Grade 50.
Its mechanical properties are not very unique, it is easily formed, machined, welded, and fabricated. It is often usedin products where surface finish is not important, like drilling equipment. 1018 Grade 50 = 1018 Grade 50 is an improved high strength-low alloy material where high strength to weight ratio is needed to produce products which Steel Material Types - DefinitionsIts mechanical properties are not very unique, it is easily formed, machined, welded, and fabricated. It is often usedin products where surface finish is not important, like drilling equipment. 1018 Grade 50 = 1018 Grade 50 is an improved high strength-low alloy material where high strength to weight ratio is needed to produce products which AR400 Steel Plate - Wearalloy 400 Plate Ford SteelRequirements for AR400 Steel Our AR400 steel plates meet all flatness and thickness requirements the 50% standards that are specified in ASTM A-6. All of the mechanical properties for the abrasion resistance steel matches the ASTM A370.