Physical properties of grade 321S31 BS 1449-2 ; Property Density kg/dm3 Temperature T °C/F Specific heat J / kgK Thermal conductivity W/mK Electric resistance µ·cm Modulus of elasticity kN/mm2 Expansion rate; 145 () 725 () 42:32:42:Solution and Aging, Annealing, Ausaging, Q+T,etc:123:Temp. °C/°F Creep strain limit (10000h Austenitic Stainless Steel - an overview ScienceDirect Austenitic stainless steels have a number of important advantages over the ferritic alloys [11, 12]:(i) generally the most resistant to hydrogen embrittlement of all the classes of steel, (ii) good baseline properties over a wide range of temperature from cryogenic to elevated temperature, and (iii) very low hydrogen permeability.The primary disadvantage of the austenitic stainless steels is
HR3 BS1449 Number:1.0332:Comparison of steel grades:NFA 36-301:1C:EN10111:DD11:DIN 1614/2:StW 22:JIS G 3131:SPHD:ASTM-SAE:A621DQ-SAE1010:UNI5867:FEP11 BS 1449-2:1983 - Steel plate, sheet and strip BS 1449-2:1983 Steel plate, sheet and strip. Specification for stainless and heat-resisting steel plate, sheet and strip Status :Superseded, Withdrawn Published:May 1983 Replaced By:BS EN 10259:1997, BS EN 10095:1999, BS EN 10048:1997, BS EN 10258:1997, BS EN 10029:1991, BS EN 10051:1991+A1:1997 BS and Equivalent EN Grades - Stealth 316Mechanical Properties that have replaced The old BS Specifications. BS1449 for cold rolled has been replaced by:Standard Scope EN10088-2 Replaces BS1449-Part 2:1983 EN10059 Covers Heat Resisting Grades BS1449 & BS1501 for hot rolled have been replaced by:Standard Scope EN10088-2 Replaces BS1449-Part 2:1983
Mechanical Properties that have replaced The old BS Specifications. BS1449 for cold rolled has been replaced by:Standard Scope EN10088-2 Replaces BS1449-Part 2:1983 EN10059 Covers Heat Resisting Grades BS1449 & BS1501 for hot rolled have been replaced by:Standard Scope EN10088-2 Replaces BS1449-Part 2:1983 CR4 in BS1449/1.3-91 standard - EQUIMETALSAbout our service. EQUIMETALS can provide exact chemical composition, mechanical properties in several states, heat treatment procedures for various purposes, as well as detailed corrosion information for over 70 corrosive mediums in several combinations of concentration and temperature.. EQUIMETALS can also offer you close equivalent and similar steels from different countries, and provide CS70 Spring Steel - Delivered Nationwide by West Yorkshire This grade is a carbon spring steel with an average carbon content of 0.70%. West Yorkshire Steel are stockholders and suppliers of hardened and tempered spring steel strip, sheet and plate supplied to specification and conforming to BS1449 and BS5770 designations. The strip is supplied in coil and can be cut to your requirements.
West Yorkshire Steel are suppliers of CS95 hardened and tempered spring steel strip conforming to BS1449 and BS5770 designations. CS95 strip is supplied in coil and can be cut and slit to your requirements. It is common for CS95 strip to be supplied with a polished surface finish; achieved by fine grinding, abrasive brushing or other similar Datasheet for Steel Grades Specialsteel HR4Physical properties, Mechanical properties, Heat treatment, and Micro structure This page is mainly introduced the HR4 Datasheet, including chemical information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc. It also contains the use of HR4,such as it is HR 15 B.S. ::Total MateriaFinding materials and property data at the click of a button By registering for the Total Materia FREE Trial it is possible to search and view the property data for over 450,000 alloys as well as find and compare equivalent materials from over 69 countries/standards in the unique, international Total Materia cross reference tables. Sign up for FREE access to Total Materia today
Jan 03, 2013 · What are CR4 Steels? CR4 steels are deep drawing quality Aluminum Killed (non-aging) mild steel revealed in ISO 3574 and are graded correspondent to SPCF steels in JIS G3141 standard. The only difference between CR3 & CR4 steels is that CR4 steels are non-aging steel and are very slowly deteriorated in mechanical properties with respect to time. Dimensional Range of CR4 Steel:CR4 SAE-AISI 1070 (C70, 1.1520, G10700) Carbon Steel The graph bars on the material properties cards further below compare SAE-AISI 1070 steel to:wrought carbon or non-alloy steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full SUBSTITUTE MATERIAL (JIS, BS, DIN ) FOR ASTM Properties Gr 55 --- 1501-151 Gr 400 SEW 680 TTSt41N 1501-161 Gr 400 1501-224 Gr 400 Gr 60 G 3115 SPV235 1501-151 Gr 430 --- 1501-161 Gr 430 1501-224 Gr 430 A-516 - Pressure Vessel Plates, Carbon Steel, for Moderate and Lower Temperature Service Gr 55 --- 1501-161 Gr 400 17155 H I
Stainless Steel Grades, Compositions & Typical Mechanical Properties EN BS AISI EN No. Composition Guide Typical Mechanical Properties (Rolled Products) Obsolete C Cr Ni Mo Others Proof Strength 0.2% Nmm 2 Tensile Strength Nmm 2 Elongation % 1.4000 403S17 410S 0.08x 12 . . . 220-250 400-600 19 Stainless Steel Material ComparisionStainless Steel Material Comparision GB1221-92 AISIASTM DIN17440 DIN17224 JIS NF A35-572/584 NF A35-576 582 BS 970 BS 1449 ISO683/13 ISO683/16 Steel Grade Equivalents Guide HillfootThe table below details similar grades to the most commonly used engineering steels. The column on the left shows some of the steel grades stocked by Hillfoot, while the middle columns show grades with similar chemistry, and the two columns on the right display grades for potential substitution.
UK B.S. BS 1449-1-1.2 HR4 Steel plate, sheet and strip. Carbon and carbon-manganese plate, sheet and strip. Specification for hot rolled steel plate, sheet and wide strip based on formability and Mechanical Properties, Chemical Element, Cross Reference, Datasheet. B.S. HR4 B.S. HR4 Datasheet. Category. Steel Strip Resources - No1 for Steel Strip Information Chemical composition BS 1449 :Part 1 :1983 greater than 3 % Of the nominal thickness of the material, at a distance Of not less than 20 mm from the edge. certain CS conditions, free from to tal be by arrangement between purchaser supplier. 0.60 0.90 0.60 0.60